Rewah Product Catalogue

You are here : Restoration
ACID NEUTRALISER

ACID NEUTRALISER

Neutralizing product for acid facade cleaning products.

ACID NEUTRALISER is used to neutralize the rinse water of facades which have been treated with REDINET.  

ANTIGRAFFITI

ANTIGRAFFITI

Colourless anti-graffiti protective coating.

ANTIGRAFFITI is a colourless moisture-proof anti-graffiti protective coating for brick, stone and similar building materials. Graffiti on these materials can be removed with DECAMUR.

AQUA MULTI

AQUA MULTI

Ready to use insect-, mould- and termite killing micro-emulsion.

AQUA MULTI is used for the preventive treatment of healthy wood and for the curative treatment of affected wood against insects and mould including dry rot (Serpula lacrymans). After the treatment, risk classification 1 and 2 according standards EN 335-1 and EN 335-2 are covered, as well as risk classification standard 3-A is covered (wood outdoors, no ground contact, resinous and hard wood).

Available documents: Technical sheet (pdf)
AQUASIL RS 8

AQUASIL RS 8

Moisture proof product based on nanotechnology and oligomer siloxanes, water based (WTCB report).

AQUASIL RS 8 is used to decrease moisture infiltration in brickwork and natural stone without modifying the water vapor permeability. By reducing moisture absorption the materials are not as easily soiled and damage by acid rain is also limited. AQUASIL RS 8 is applied on brick, stone, etc…. on the basis that these materials are sufficiently porous. The product is not suited to be applied on non-porous surfaces like blue stone, marble, glazed stone… AQUASIL RS 8 is also not suited to be applied onto surfaces covered with organic paints. AQUASIL RS 8 is a water based product and therefore causes no smell which possibly might arise when using solvent based products.  AQUASIL RS 8 can not be applied on former surfaces treated with hydrofobic products, in suchlike situations we recommend using REDISIL S or STONEGEL.

Realisations with this product: Abbey of Westmalle
ARTICLEAN 02

ARTICLEAN 02

Specific cleaning and degreasing product for epoxy applications.

ARTICLEAN 02 is applied as a rinsing and cleaning product to clean the material which has been used to apply epoxy or polyurethane. ARTICLEAN 02 is used as well to degrease epoxy floors before additional finishing layers like polyurethane coatings are applied.

ARTIPOX HR/RB-2

ARTIPOX HR/RB-2

Self-levelling epoxy mortar for polymeric chemical beam head restoration.

ARTIPOX HR/RB-2 is especially designed for the restoration of beam heads and beam head joints that are damaged by wood rot and insects.

Realisations with this product: Merksplas-Kolonie
ARTIPOX I

ARTIPOX I

Thin-fluid epoxy formula for the injection of cracks.

Consolidation of cracks in concrete, wood and stone.

ARTIPOX MULTI

ARTIPOX MULTI

Universal thin-fluid epoxy.

Floor covering- acid-resistant treatment of flooring through impregnation- nonskid coating for floors, stairs and tresholds Concrete repair mortarAs mortar binder for minor repair workGrout massFor grouting of cracks and horizontal fissures in floorsGlueFor wood, stone, metal and ceramic materials. This glue can be thickened to satisfaction with ARTIPOX TIXO powder (1).Impregnating massTo solidify concrete surfaces, sand cement surface dressing and brick masonry.FillerPowerful adhesive, hard and shrink-proof filler for wood, metal, concrete, stone, surface dressing(1) ARTIPOX TIXO powder is a thickener for synthetic resins.

ARTISIL B10

ARTISIL B10

Moisture proof product based on silanes 10% with maximum alcali stabilty.

ARTISIL B10 is used to decrease moisture infiltration in concrete constructions and masonry in concrete stone without modifying the water vapour permeability. By reducing moisture absorption the materials are not as easily soiled and damage by acid rain is also limited. ARTISIL B10 is applied on concrete, masonry in concrete stone and silicate stone, on fresh jointing on the basis that these materials are sufficiently porous. The product is not suited to be applied on non-porous surfaces like blue stone, marble, glazed stone,…ARTISIL B10 is also not suited to be applied onto surfaces covered with organic paints. 

ARTISIL SVS 100

ARTISIL SVS 100

Stone hardener on the basis of ethyl silicic acid ester 100%.

ARTISIL SVS 100 is an impregnating product on the basis of ethyl silicic acid ester designed to harden powdery building materials without radically changing their characteristics. All absorbent non-layered types of stone can be hardened such as:- gravel-bound, clay-bound and limestone-bound sandstone (Balegem, Chauvigny, etc…)- concrete and brick

Realisations with this product: Red Star Line Museum Antwerp Abbey of Affligem
ARTISIL SVS 75

ARTISIL SVS 75

Stone hardener on the basis of ethyl silicic acid ester 75%.

ARTISIL SVS 75 is an impregnating product on the basis of ethyl silicic acid ester designed to harden powdery building materials without radically changing their characteristics. All absorbent non-layered types of stone can be hardened such as:- gravel-bound, clay-bound and limestone-bound sandstone (Balegem, Chauvigny, etc…)- concrete and brick

ARTIWOOD

ARTIWOOD

Epoxy mortar for restoration of wooden sections or wooden beams.

Both structural and decorative repair work/restoration of wooden sections affected by mould and insects: - affected window frames- wooden beams- wooden statues and sculptures

BOTAMENT M21 FLEXLIJM

BOTAMENT M21 FLEXLIJM

Superieur quality flexible adhesive.

BOTAMENT M21 FLEXLIJM is used as an adhesive for:- MEMBRASEC-BLUE- MEMBRASCREEN- Sandstone and stoneware - Hand-made tiles - Small and medium-sized mozaics- Insulation panelsVery smooth panels (e.g. rigid foam panels) must be roughened.Suitable surfaces for the application of BOTAMENT M21 FLEXLIJM:- Concrete, lightweight concrete and cellular concrete- Solid masonry- CS II, CS III and CS IV renderings, in compliance with NEN EN 998, and plaster coatings, in compliance with NEN EN 13279 (compression resistance ≥ 2.5 N/mm²)- Old tiles- Plasterboard, gypsym board and fibre plaster boardBefore using as an adhesive for MEMBRASEC-BLUE and MEMBRASCREEN, any coverings that contain salt and moisture should be removed. 

Available documents: Technical sheet (pdf)
Realisations with this product:
CEMENTREMOVE

CEMENTREMOVE

Cement residue remover, free of phosphoric and hydrochloric acid.

CEMENTREMOVE is used to remove cement residue and lime efflorescences on masonry. 

DECAMUR

DECAMUR

Solvent free powerfull stripper for facade paint, safe to use.

DECAMUR is a new developed stripper which is particularly suited to remove paint of facades. In contrast to the most paint strippers, this product is water-based and completely free of solvents. DECAMUR is in such a way safe to use that it can be sprayed airless. The product is likewise to be used inside without any danger. DECAMUR can be used to remove water-based paints and emulsion paints on brick, natural stone, bluestone, marble, concrete, …. Not suitable for mineral paints for example such as lime paint. 

Realisations with this product: Abbey of Affligem
DECASTRIP MAX

DECASTRIP MAX

Powerful, fast acting paint stripper for outdoor use, mehtylene chloride free.

DECASTRIP MAX removes layers of paint from wood, stone, metal, etc.  It enables you to strip away coats of paint made from a wide range of ingredients, such as latex, acrylate, oil, cellulose, alkyd, chlorinated rubber, polyurethane and epoxy. DECASTRIP MAX can also be used for removing adhesives, tags and graffiti.

DRAIN TYPE 20

DRAIN TYPE 20

HDPE dimpled membrane as part of drainage systems.

DRAIN TYPE 20 is used as a drainage membrane.

Available documents: Technical sheet (pdf)
Realisations with this product:
ECONOSIL

ECONOSIL

Moisture proof product on the basis of a siloxane-organometal 10% (WTCB report).

ECONOSIL is used to decrease moisture infiltration in brickwork and natural stone without modifying the water vapour permeability. By reducing moisture absorption the materials are not as easily soiled and damage by acid rain is also limited. ECONOSIL is applied on brick, stone and related building materials on the basis that these materials are sufficiently porous. The product is not suited to be applied on non-porous surfaces like blue stone, marble, glazed stone. ECONOSIL is also not suited to be applied onto surfaces covered with organic paints or on synthetic plaster. 

ECONOSIL INJECT

ECONOSIL INJECT

Injection product, 10% siloxane-organometal in aliphatic solvent.

ECONOSIL INJECT is used to prevent rising moisture in masonry.

FACONET 20

FACONET 20

Environmentally safe cleaning product for weathered and dirty exterior walls.

FACONET 20 is a cleaning product principally for the safe cleaning of natural stone , concrete walls and decorative plaster. It has been formulated to clean in a non-aggressive way making FACONET 20 a very suitable product to be used in the cleaning of historic building and art works. Not only will dirt deposits and soot be removed but also typical weathering characteristics such as plaster incrustation can be cleaned without negatively affecting the natural patina. In actual trials to date exceptional results have been obtained on limestone, sandstone, bluestone, marble, concrete, brick, enamelled stone and decorative plaster.  

GELIFUGE NEW

GELIFUGE NEW

Water repellent surface product.

GELIFUGE NEW is used to reduce the infiltration of moisture in porous masonry without significantly reducing water vapour permeability. Because of their reduced moisture absorption, the materials become dirty less quickly and any changes caused by acid rain are also limited. GELIFUGE NEW can be applied onto bricks, sand-lime bricks, roof tiles, etc… on the basis that these materials are sufficiently porous. This product is not suitable for application on non-porous surfaces, such as natural blue stone, marble, glazed bricks, etc., or on surfaces covered with organic paint. If applied to natural stone, the product may cause the surface to become darker or discoloured in places. As these effects may not be desirable, we do not recommend that you use this product on natural stone.

GLAS POLIJST PASTA

GLAS POLIJST PASTA

Polishing compound for transparent glass.

GLAS POLIJST PASTA is used to remove deposits and lime scale, among others, from glass by polishing the surface.

Available documents: Technical sheet (pdf)
INDUSIL MS 3000 ISO

INDUSIL MS 3000 ISO

Virtually odourless polyvalent injection product to rising damp.

INDUSIL MS 3000 ISO is a solvent based injection product offering a sufficient protection to rising water. INDUSIL MS 3000 ISO is injected just above floor level. The product polymerizes in the capillaries and pores in order to form a watertight area preventing capillary rising damp.

MEMBRASCREEN

MEMBRASCREEN

Complete final coating system after rising damp injection.

The Rewah range includes various products for the treatment of walls against rising damp. We all know that these products provide an effective barrier against this problem within 48 – 72 hours. However, it can take up to 12 or more hours for walls to dry out fully, as residual moisture remains present in walls for years and needs to evaporate. Until now, we were always advised to wait until walls were fully dry before adding a final coating. In addition, the presence of salts represents a secondary factor for most walls that have been affected by rising damp. Some salts also become crystallised during drying and concentrate on the wall surface. Other salts behave “hygroscopically”, which means that they absorb moisture from the ambient air, while the wall surface remains damp, even after being successfully treated against rising damp. With this in mind, Rewah has developed the MEMBRASCREEN coating system, which enables you to cover the entire wall surface before it is fully dry and/or neutralise the hygroscopic behaviour of the salts.

Available documents: Technical sheet (pdf)
MEMBRASEC

MEMBRASEC

Salt blocking membrane after treatment against rising damp.

The Rewah range includes a choice of products for the treatment of walls against rising damp. It is well known that these products form an efficient barrier against this phenomenon within 48 to 72 hours. However, the thorough drying of the wall can take up to 12 months and over because all the remaining moisture that was stocked in the wall for years must evaporate. It is currently advised to wait with the final finishing of the walls till they are completely dry. Furthermore, the presence of salts is a secondary phenomenon for most walls that were subjected to rising damp. When the wall is drying, some salts will crystallize and concentrate on the wall surface. Other salts are so-called hygroscopic salts which means that they subtract moisture from the ambient air causing the wall to remain damp at the surface even after a successful treatment against rising damp. In order to allow the user to finish all the walls before they are dry and/or to neutralize the hygroscopic property of the salts, Rewah proposes the MEMBRASEC finishing system.

Available documents: Technical sheet (pdf)
Realisations with this product: Merksplas-Kolonie
MONOLYS

MONOLYS

Ready to use natural hydraulic lime mortar for the finishing of interior walls

MONOLYS can be used as an interior wall coating for monuments and buildings. It is also extremely breathable. The coating can be applied in 1 or 2 steps, either mechanically or manually. Due to its very fine granulometry, the coating can be finished with lime or hybrid silane-based paint. 

MONUCLEAN BF 4 NA

MONUCLEAN BF 4 NA

Peelable, elastic odorless cleaning paste for interior.

MONUCLEAN BF 4 NA is used for dry cleaning of dirt sediments, such as dust, earthy sediments, bird droppings, blackening, dense smoke, soot, etc. The product is also effective against superficial stains of soot and dust that have penetrated into the material through moisture. MONUCLEAN BF 4 NA is very suitable for inside cleaning of various substrates, such as brick, concrete and cement-bound artificial stone, limestone, sandstone, chalkstone, glazed brick, marble, plaster, paints, plastics, metal, … MONUCLEAN BF 4 NA is very suitable for industrial cleaning thanks to its high processing efficiency.

MONUCLEAN BF 4 NA EXTERIOR

MONUCLEAN BF 4 NA EXTERIOR

Peelable, elastic odorless cleaning paste for exterior.

MONUCLEAN BF 4 NA EXTERIOR is used for dry cleaning of dirt sediments, such as dust, earthy sediments, bird droppings, blackening, dense smoke, soot, etc. The product is also effective against superficial stains of soot and dust that have penetrated into the material through moisture. MONUCLEAN BF 4 NA EXTERIOR is very suitable for outside cleaning of various substrates, such as brick, concrete and cement-bound artificial stone, limestone, sandstone, chalkstone, glazed brick, marble, plaster, paints, plastics, metal, … MONUCLEAN BF 4 NA EXTERIOR is very suitable for industrial cleaning thanks to its high processing efficiency.

MONULIT

MONULIT

Mineral restoration mortar for stone (KIK + WTCB report).

- Restoration of most types of stone except those with a too dense crystal structure (e.g. marble, granite, etc.). - Restoration of brick and terracotta. - For local repair work of flat surfaces, surface relief, ornaments and sculptures. With MONULIT historic outside walls and monuments can be restored in the most faithful manner because:- The product is very easily workable (ornament and surface relief).- Limitation of every existing surface texture and stone colour is possible.- The restoration is ageing in the same way as stone.Particular characteristics are:- Repair work is possible in one go- No protection needed from sun and wind- Shrink-resistant hardening- Frost-resistant

MONULIT TOP LIQUID

MONULIT TOP LIQUID

Binder for special decorative techniques with Monulit.

MONULIT TOP LIQUID is used as a binder in the preparation of thin decorative coatings with MONULIT powder as stone repairing substance. It can also be used as a binder for pigment in order to colour or give a patina when necessary repairs are carried out with MONULIT mortar.

OLEOFUGE F

OLEOFUGE F

Water and oil repellant impregnation product. Water based.

OLEOFUGE F is used to reduce the infiltration of moisture into porous building materials, without causing any significant changes to its water vapour permeability. It also makes the surface water and oil repellent, so that the materials become soiled less quickly. This product is therefore ideal for application in urban and industrial environments. OLEOFUGE F can be applied to facades, bricks, natural stone, concrete, tiles, and on horizontal concrete surfaces, provided they are sufficiently porous. In this way, horizontal surfaces will be protected against infiltration of metaborates. OLEOFUGE F is not suitable for application on surfaces that have been covered with organic paints or synthetic coatings. 

OMNICLEAN CONC

OMNICLEAN CONC

Biodegradable, concentrated, industrial cleaning agent.

OMNICLEAN CONC. is developed especially for the cleaning and the brightening of heavily polluted surfaces. This product removes dirt of different origins like the sediments and stains of mineral, animal and/or vegetable oils and fats, the most diverse atmospheric contaminations, plant growth, food rests, bird droppings, rubber marks, … OMNICLEAN CONC. is perfectly suitable for the cleaning of various materials such as concrete, enamelled bricks, marble, decorative plasterwork, paints, synthetic materials, granitic coatings, metals, …

Realisations with this product:
REDINET

REDINET

Acid cleaning agent for facades.

REDINET is mainly used for the cleaning of dirty brick, with the exception of highly compact or porous brick. Provided that REDINET is applied with due care, architectonic concrete and washed concrete can be cleaned with equal ease.

REDISIL S

REDISIL S

Moisture proof product based on oligomer siloxanes 10% (ATG + WTCB report).

REDISIL S is used to decrease moisture infiltration in brickwork and natural stone without modifying the water vapour permeability. By reducing moisture absorption the materials are not as easilly soiled and damaged by acid rains is also limited. REDISIL S is applied on brick, stone, roof tiles, etc… on the basis that these materials are sufficiently porous. The product is not suited to be applied on non-porous surfaces like blue stone, marble, glazed stone,… REDISIL S is also not suited to be applied onto surfaces covered with organic paints or on synthetic plaster. 

REWACLEAN PRO

REWACLEAN PRO

Super concentrated cleaning material for building materials.

REWACLEAN PRO is used to clean persistent contaminated slate roofs, tiles, concrete, plastering, masonry, facade paint and related alcaline resistant building materials. 

REWAGEL INJECT 3A+

REWAGEL INJECT 3A+

Concentrated gel emulsion, silanes/siloxanes, against rising damp (WTCB report).

REWAGEL INJECT 3A+ is a solvent-free product which is easy to use and environmentally sound, for permanent, effective protection from rising damp. REWAGEL INJECT 3A+ is pumped, by means of a simple system, into holes drilled in the foot of the wall. The product is sublimated into the capillaries of silicate building material – in other words, it changes from the gel phase to a vapour phase. The active ingredient thus spreads out evenly throughout the capillary system of the building material, whether wet or dry, and forms a waterproof damp-proof course at the foot of the wall to prevent rising damp by capillarity. 

REWASIL AVT

REWASIL AVT

Water repellent surface product. Leaves no marks.

REWASIL AVT is used to reduce the infiltration of moisture into brickwork without causing any significant changes to its water vapour permeability. Due to their reduced moisture absorption, the materials become soiled less quickly and the effects of acid rain are also limited. REWASIL AVT can be applied to bricks provided these bicks to be sufficiently porous. This product is specially designed for façades with a high proportion of blue stone and/or glass, as it does not leave behind any marks, if it is spread with a brush before drying.

REWAX-AG

REWAX-AG

Anti-graffiti protective coating for brick, concrete, stone, ...

REWAX-AG is used as an anti-graffiti protective coating for brick, concrete, stone and other mineral building materials. Metal, synthetic material and painted surfaces can also be protected with REWAX-AG.

SALTBLOCK-2K

SALTBLOCK-2K

Salt blocking coating.

Due to their hygroscopic nature salts such as nitrates and chlorides can cause permanent damage and/or moisture in building materials and their finishing layers. SALTBLOCK-2K seals these salts so that these damages do not reoccur. The coating is used as a pre-treatment for paint, plaster and wall paper or as a subsequent treatment following injections against rising damp, sealing cellars, …

SALTREMOVE

SALTREMOVE

Acid product for neutralizing and eliminating salt efflorescences.

SALTREMOVE is used to neutralize water soluble salts on affected masonry.  

SECAUGEL INJECT 2

SECAUGEL INJECT 2

Concentrated gel emulsion in cases, against rising damp (WTCB report).

SECAUGEL INJECT 2 is a solvent-free product which is easy to use and environmentally sound, for permanent, effective protection from rising damp.  SECAUGEL INJECT 2 is pumped, by means of a simple system, into holes drilled in the foot of the wall.  The product is sublimated into the capillaries of silicate building material – in other words, it changes from the gel phase to a vapour phase.  The active ingredient thus spreads out evenly throughout the capillary system of the building material, whether wet or dry, and forms a waterproof damp-proof course at the foot of the wall to prevent rising damp by capillarity. 

SOCLI CHAUX NHL 3,5 GRIJS

SOCLI CHAUX NHL 3,5 GRIJS

.

Available documents: Safety sheet (pdf)
SOCLI CHAUX NHL 3,5 WIT

SOCLI CHAUX NHL 3,5 WIT

.

Available documents: Safety sheet (pdf)
SOCLI RENOCHAUX NHL 2 WIT

SOCLI RENOCHAUX NHL 2 WIT

.

Available documents: Safety sheet (pdf)
STONEGEL

STONEGEL

Moisture proof product, water carried and gelatinuous, base of silane-siloxane 25% (WTCB report).

STONEGEL is used to decrease moisture infiltration in porous masonry and concrete constructions without modifying the water vapor permeability. By reducing moisture absorption the materials are not as easily soiled and damage by acid rain is also limited. STONEGEL is applied on brick, stone, silicate stone, concrete and cement plastering, roof tiles, etc… on the basis that these materials are sufficiently porous. The product is not suited to be applied on non-porous surfaces like blue stone, marble, glazed stone,…STONEGEL is also not suited to be applied onto surfaces covered with organic paints. If applied to natural stone, the product may cause the surface to become darker or discoloured in places. As these effects may not be desirable, we do not recommend that you use this product on natural stone.

© Rewah 2018 - info@rewah.com - Privacy Statement